Data Video RMC-180 Instruction Manual

Full HD PTZ Camera PTC-100 INSTRUCTION MANUAL www.datavideo-tek.com

10SW1: ID Setup: PTZ cameras can be connected in series of up to 225 devices; each PTZ camera has its own ID number and may not be repeated.

11 DIP switch setting, as shown below: Set to 000, then the image d

12PTC-100 Installation Guide Step 1 Set the IMAGE FLIP switch on the rear panel to ON. Step 2 Attach the retaining wire to the junction box in th

13Step 4 Attach the ceiling bracket (A) to the bottom of the camera using the 3 screws. Align the screw holes on the bottom of the camera with those

14Step 5 Insert the protrusions raised on the ceiling bracket (A) into the spaces prepared in the ceiling bracket (B), and temporarily attach them by

15Step 7 Connect the cables to the connectors on the rear of the camera. Removing the camera Step 1 Remove the 3 screw

16OSD Operational Description ◎Selection marked as "*", represents factory default value Menu Tree Structure MAIN MENU MODE ITEM NOTES

17 CAMERA SETUP DAY/ NIGHT AE DEFAULT Return to default setup RETURN Return to previous setup page DAY* DEFAULT Return to default setup RETURN Re

18VIDEO SETUP 1080/ 50i (PAL) HORIZONTAL 0> 1> ...> 96*> 97> ...> 198> 199 VERTICAL 0> 1> ...> 36* > 37> ...>

19CAMERA SETUP > FOCUS SETUP Users can setup focus application. Factory settings as shown below:  MODE: This function is used for setti

2Contents Warnings and Precautions ... 3 Warran

20 GAIN LIMIT: Setup Gain Limit, setup range = 0~28 (Default Setup: 6).  SHUTTER: Shutter Speed consist of 5 types of mode: NTSC: 1/1，1

21CAMERA > WHITE BALANCE Users can setup white balance application. Factory settings as shown below:  MODE: Three types of WB mode setup

22CAMERA SETUP > EFFECT SETUP User can setup some image application and effect. Factory settings are as shown below:  NEGATIVE: Negativ

23 SPEED (DPS): Setup the moving speed, higher the value faster the speed.  DWELL TIME (SEC): Setup the dwell time after cruise fun

24OSD SETUP  ID DISPLAY: To reveal or hide ID, can be set to ON/ OFF.  TITLE DISPLAY: To reveal or hide Title, can be set to ON/ OFF.

25

26

27Remote Controller Button Description Menu Setup PTC-100 requires HDMI monitor to browse the current setup sta

28Item Illustration Function Description 1 Color Bar Setup (MODE) Use the MODE button to setup and adjust the screen brightness and color

29Item Illustration Function Description 6 Auto Focus Control (A/ FOCUS) To focus the camera on a subject automatically Press the A/ FOCUS button.

3Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this

30Item Illustration Function Description 12 Enter/ Exit Camera Menu Option Enter or Exit Camera Menu Option 13 Zoom in/ Zoom Out Button Enl

31Dimension

32Specification Item No. PTC-100 SD/ HD Description HD-SDI/HDMI + CVBS PTZ Camera Video Image Device 1/3” Sony Exmor 3.0MP CMOS sensor Picture Ele

33Motion Detection - MD Sensitivity - Alarm - Privacy Masking - White Balance Auto(ATW) / Manual / Push Auto Gain Control Auto/Manual (6 to 28 dB,

34Day / Night IR-Cut filter Removable Yes IR Distance - LED (pcs/angle) - Light Transistor - Wavelength - Lens Lens Type Mototized 20X Zoom Focal Len

35Protocol Pelco D/ P; Sony VISCA Baud Rate 9600bps Video Output (HD) HD-SDI (BNC)/ HDMI Video Output (SD) BNC Video Format Output 1Vp-p/ 75Ohms

36Service & Support It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in s

4Warranty Standard Warranty • Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of purch

5Introduction Thank you for purchasing the Datavideo PTC-100 Full HD PTZ Camera. We hope you will be pleased with your purchase, and with what yo

6Connections & Controls PTC-100 Front View Item Illustration Name Description 1 Lens Built-in 1/3” Sony Exmor 3.0MP CMOS HD colo

7PTC-100 Rear View Item Illustration Function Description 1 SW2: IRID&DVIP Setup Bold letters indicates factory default value. Setup S

8Item Illustration Function Description 3 HD-SDI OUT Video signal output 800mV+-10% 75Ω BNC 4 CVBS OUT Video signal output CVBS 1. 0

9PTC-100 Bottom View Item Illustration Function Description 1 Shown above Tripod screw hole 2 SW1: DIP Switch setup PTZ cameras c